Cloudray Leadshine M542C 2 Phase Stepper Driver

SKU: SMD10L2PM542C
Cloudray Leadshine M542C 2 Phase Stepper Driver
Cloudray Leadshine M542C 2 Phase Stepper Driver
Cloudray Leadshine M542C 2 Phase Stepper Driver
Cloudray Leadshine M542C 2 Phase Stepper Driver
Cloudray Leadshine M542C 2 Phase Stepper Driver

Cloudray Leadshine M542C 2 Phase Stepper Driver

SKU: SMD10L2PM542C
Regular price $ 45.00 USD Sale price $ 32.00 USD Save $ 13 USD
/
  • Notification: Only Offer Lifetime Tech Support and Marking/Engraving Parameters for Orders on www.cloudraylaser.com. Not Responsible for orders from other third-party platforms or offline dealers.
  • Secure payments
  • In stock, ready to ship
  • Inventory on the way
Shipping calculated at checkout.

 


 

 

Parameters

M542C

Min

Typical

Max

Unit

Output Current

1.0

-

4.2 (3.0 RMS)

A

Supply Voltage

20VAC

36VAC

50VAC

V

Logic Signal Current

7

10

16

mA

Pulse Input Frequency

0

-

300

kHz

Step Revolution

400

 

25600

Pulse/Rev

Isolation Resistance

500

Suitable Stepper Motors

NEMA 16,17,23

 


 

 

P1 Function

M542C Details

PUL+

Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each rising or falling edge active (set by inside jumper J1); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active at high level or low level (set by inside jumper J1, J2). For reliable response, pulse width should be longer than 1.5µs. Series connect resistors for current-limiting when +12V or +24V used. The same as DIR and ENA signals.

PUL-

DIR+

DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J3), this signal is counter-clock (CCW) pulse,active at high level or low level (set by inside jumper J1, J2). For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-drive wiring match. Exchanging the connection of two wires for a coil to the drive will reverse motion direction.

DIR-

ENA+

Enable signal: This signal is used for enabling/disabling the drive. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the drive and low level for disabling the drive. Usually left UNCONNECTED (ENABLED).

ENA-


 

 

P2 Function

M542C Details

+Vdc

Power supply, 20~50 VDC, Including voltage fluctuation and EMF voltage.

GND

Power Ground.

A+, A-

Motor Phase A

B+, B-

Motor Phase B

1.Cloudray LiteMarker Fiber Marking Machine Product display: https://www.youtube.com/watch?v=TaT7vyz__bY

2.Litemarker Laser Marking Machine Unboxing demo: https://www.youtube.com/watch?v=QIBQ0jNuyZg

3.Beginner's Guide EZCAD2 Software Tutorial : Overview of Software Functions: https://www.youtube.com/watch?v=aQ8bWZuFZYM

4.EZCAD2 Driver Uninstall and Driver Installation: https://www.youtube.com/watch?v=xo7QmuvEhK4 

5.Rotary shaft installation: https://www.youtube.com/watch?v=LJOMZYTwfVQ

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

QS-30 EasyMarker 30W Portable Laser Engraver Fiber Marking Machine
from $ 2,299.00 USD
Recently viewed